Serial Pi Plus

RS232 Serial Port for the Raspberry Pi

£13.19 each (excluding VAT: £10.99)
107 available
Product Code:Serial Pi Plus (single)
EAN:7426787870194
Add a Mounting Kit Four Pack
for only £3.49 each ex vat
Order Mounting kit to use on our Raspberry Pi boards
Share: Twitter Facebook
  • RS232 Master Serial Port.
  • Control the Raspberry Pi over RS232 or connect to external serial accessories.
  • Stackable with other Raspberry Pi Hats.
  • Mounting holes for use with the AB Electronics UK mounting kits (sold separately)

The Serial Pi Plus is a communication board supporting the RS232 serial protocol, designed for use on the Raspberry Pi and other compatible single-board computers.

The RS232 serial port is connected to the UART port on the Raspberry Pi using a MAX3232 or ICL3232ECBNZ* interface. The MAX3232 and ICL3232ECBNZ* ICs convert the 3.3V UART port to RS232 voltages, allowing communication with RS232 compatible devices over a DB9 serial cable. With a null-modem cable, the board allows terminal access with Linux on the Raspberry Pi using a terminal application.

An array of 2.54mm pitch holes with 3.3V and 5V connections are also provided on the PCB, allowing you to build additional circuits on the board.

Please note that you can only use one Serial Pi Plus board on a Raspberry Pi. If stacking with other boards, we recommend putting the Serial Pi Plus at the top of the stack due to the height of the DB9 connector.

Connecting to the RS232 Port: You need to use the latest Raspbian Jessie release and disable the built-in Bluetooth to use the Serial Pi Plus on the Raspberry Pi 3 or Raspberry Pi Zero W; see our KB page for the config changes needed.

The RS232 port on the Serial Pi Plus can be accessed through the male DB9 socket or the solder points on the PCB. The DB9 socket is configured as a master socket, as you will find on desktop computers, allowing you to connect external serial devices with a standard RS232 cable.

*Due to global component shortages, Serial Pi Plus boards manufactured after 23/11/2022 may use the Intersil ICL3232ECBNZ RS232 interface IC. The ICL3232ECBNZ is a pin-compatible replacement for the Texas Instruments MAX3232.

Legacy Serial Pi Versions

See our KB article for previous versions of this board.

Compatibility

We have tested the Serial Pi Plus on the following platforms.

Model Status
Raspberry Pi Model A / B
Raspberry Pi 1 Model A+ / B+
Raspberry Pi 2 Model B
Raspberry Pi 3 Model A+ / B / B+
Raspberry Pi 4 Model B
Raspberry Pi 5
Raspberry Pi Zero
Raspberry Pi Zero W / Zero 2 W
Raspberry Pi Compute Module 4 IO Board
Raspberry Pi 400
Orange Pi
Odroid

*You need to use the latest Raspberry Pi OS release and disable the built-in Bluetooth to use the Serial Pi Plus on the Raspberry Pi 3, 3+ and 4. See our KB page for the config changes needed.

Product thumb
Serial Pi Plus
£13.19 each (excluding VAT: £10.99)

Technical Details

Input Ratings & Specifications

Spec
Ratings
Supply Voltage
3.3V to 5.5V
Logic Voltage at UART Port
3.3V
Maximum Data Rate
250 kbits/s
RS232 Input voltage range
-25V to +25V
RS232 Output voltage range
-13.2V to +13.2V

3D CAD Model

Click to downloadSerial Pi Plus - 3D CAD File (STEP Format)

Schematic

Click to View
View the schematic PDF.

Mechanical Drawings

Click the image to enlarge.

Product thumb
Serial Pi Plus
£13.19 each (excluding VAT: £10.99)

Assembly Instructions

The Serial Pi Plus is supplied with the 40-pin GPIO connector, and the DB9 connector is unsoldered. 

Before using the Serial Pi Plus, you need to solder both connectors onto the PCB. We suggest soldering the 40-pin GPIO connector first and then the DB9 connector. 

To make assembly easier, we have designed a PCB header assembly jig which you can download and print.

Watch the assembly video, best viewed in 1080p high-quality mode:

Assembly Guide Video

Watch our assembly guide on YouTube. (opens in a new window)

PCB Header Assembly Jig

Download and print our PCB Header Assembly Jig to hold your circuit board when soldering the header pins.

PCB header assembly jig

RS232 Port

The pin-out connections for the RS232 port are shown below:

Pin Usage
1 N/C
2 RX (data receive)
3 TX (data transmit)
4 N/C
5 Ground
6 N/C
7 N/C
8 N/C
9 N/C

DB-9 Connector

DB9 connector as viewed from the front of the Serial Pi Plus

Using the RS232 port for terminal connections

The RS232 port can be used for remote terminal connections on the Raspberry Pi, allowing remote access and control without needing an ethernet connection. You will need to use a Null-Modem cable to connect the Serial Pi to a desktop computer. A wiring diagram for making a Null-Modem cable can be found below. For details on configuring the RS232 communication on the Raspberry Pi, visit our knowledge base.

Null-Modem Cable

Null modem wiring diagram

Connector 1 Connector 2 Function
2 3 Rx ← Tx
3 2 Tx → Rx
5 5 Ground

You may also like

Important Information

This development board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by abelectronics.co.uk to be a finished end-product fit for general consumer use. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. Persons handling the product(s) must have electronics training and observe good engineering practice standards. This development board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives. Note: documents in Portable Document Format (PDF) require Adobe Acrobat Reader 5.0 or higher to view, download Adobe Acrobat Reader or other PDF reading software for your computer or mobile device.